2 post hoist Telescopic arms
For those hard-to-reach lifting points, the AL-9500CF is fitted with telescopic arms. The longer arm has a two-stage extension whilst the shorter arm has a 3 stage extension.
2 Post Hoist – 4500kg / 4.5 Tonne Lifting Capacity
With a lifting capacity of 4500kg / 4.5 Tonne, the 4.5T 2 post car hoist is perfect for lifting 4WD such as Toyota Landcruisers and Nissan Patrols. The 2 post clearfloor hoist allows the use of transmission jacks, oil drainers, and tool chests to be wheeled around freely underneath the vehicle. This hoist offers even greater options with the additional purchase of a 4.5T 2 Post height extender kit that takes maximum lift height from 3700mm to 4700mm.
- Worksafe Design Registered gives you the peace of mind knowing the car hoist complies with Australian Standards 1418.9
- Heavy Duty Hydraulic cylinders mounted within the columns drive the lifting carriages for a smooth seamless lift of the vehicle (no chains)
- Powerful 2.2kw 240v single phase or 415v three-phase hydraulic power units available.
- Safety Locking Ladders fitted to each column (100mm increments) with manual lock release operation
- Two-stage screw adjustable pads and chassis pads included
- Safety Limit Switch cuts out the hydraulic power unit when maximum height is reached.
- Low Voltage 24volt controls for added safety
Adjustable Pads & Height adaptors
The two-stage adjustable pads fitted to the AL-9500CF allow for 50mm of adjustment and for those lifted 4WD the included 100m height adaptors and chassis pads increase the lifting height of the vehicle.
Auto locking arms
We take safety seriously here at AAQ that’s why we fitted automatic locking arms to our range of 2 post car hoists. Once the lift is operated and the arms lift off the ground the locks engage locking the arms in place.
Single-sided safety lock release lever disengages the locking mechanism when lowering the vehicle.
Single or THREE-PHASE options
The AL-9500CF can be purchased in either single phase 240v 15amp or 3 phase 415v. The powerful hydraulic power units provide enough pressure to lift up to 4500kg / 4.5 Tonnes, perfect for large 4WD such as Toyota Landcruisers or Nissan Patrols.
engineered base frames
Optional engineered base frames are available and are recommended to be used if your concrete floor does meet the recommended 150mm thickness.
Concrete requirements
150mm thick concrete steel mesh reinforced (25-30 MPA)
DON’T forget hydraulic oil!
Hydraulic oil is not supplied with the hoist, the AL-9500CF requires 12-15L of ISO 32 Grade Hydraulic Oil.
We can supply 5L 32 grade Hydraulic Oil for pick up only, we cannot freight oil.
2 Post Hoist dimensions
2 Post Car Hoist
To install an AL-9500CF hoist into your workshop or garage you will require 3.9m high roof at a minimum. Be sure you have adequate clearance before purchasing.
| Power unit option | Single Phase, Three Phase |
|---|
WHAT'S INCLUDED
- 2 post hoist
- M18 concrete anchor through bolts
- Single phase 240v 15amp motor / 3 phase 415v 20amp motor
- 60mm lift adapters
- Adjustable Pads
- Chassis Pads
- Installation Manual
What’s Not Included?
- Installation
- Hydraulic Oil
- Electrical Connection (Electrician Required)
Workshop requirements
- 150mm steel mesh reinforced concrete (25-30 MPA)
- Minimum Ceiling height of 3.9m (3.75m low height setting)
(Engineered base frames available for 100 – 125mm concrete footing)
Warranty and Certification
- 5-year structural warranty*
- Australian Standard WorkSafe Design Registered
Specifications
• Height overall: 3850 mm or 3600mm for lower height setting.
• Width overall: 3390mm
• Lifting height: 1950 – 2010mm
• Lowest height: 115 – 175mm
• Lifting capacity: 4500kg
• Power: 240V/50Hz/1Ph (15 Amp) or 415V/50Hz/3Ph (20 Amp)
• Gross weight: 830kg
• Packing Size: 2850*940*450 mm
Features
• Clear floor design for ease of working with transmission or under lift jacks, oil drainers or tool chests
• High quality powder coated finish
• Professional quality power unit
• Safety shut off valve
• Long arm two stage telescopic
• Short arm three stage telescopic
• Two stage screw adjustable pads
• Rubber door protectors
• Hydraulic cylinder covers
• Easy operation manual lock release
• Top limit switch cut-off
• 4 x 60mm height adaptors & 4WD extensions pads include
Delivery
We’ll help find the best, most reliable rate and send you the invoice. Please contact us for a quote.
Only logged in customers who have purchased this product may leave a review.
Related products
Sale!
Single Post Hoists
Original price was: $5,980.00.$5,382.00Current price is: $5,382.00.
Reviews
There are no reviews yet.